The organization keeps for the procedure concept “scientific administration, superior quality and effectiveness primacy, shopper supreme for 18 Years Factory Omh Mh Bmh 155 Rpm Orbit Hydraulic Motor 20 Hp For Putzmeister, Each of the time, we have been paying focus on all facts to insure each product or service happy by our clients.
The organization keeps for the procedure concept “scientific administration, superior quality and effectiveness primacy, shopper supreme for Hydraulic Parts, Omh Motor, Orbit Motor, We integrate all our advantages to continuously innovate, improve and optimize our industrial structure and product performance. We are going to always believe in and work on it. Welcome to join us to promote green light, together we will make a better Future!
GENERAL INFORMATION
Cycloidal gear motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Cycloidal gear motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into moto which is then delivered via the motor’s output shaft. Cycloidal gear motors have high starting torque and constant output torque at wide speed range.
DISTIBUTORVALVE
GR, GRS series motors have spool valve: the distributor valve has been integrated with the output shaft. The cardan shaft rotates distributor valve and transfers mechanical energy from gerotor set to output shaft. The valve has hydrodynamic bearings and has infinite life when load ratings are not exceeded.
GEAR WHEEL SET
There are two forms of gearwheel set:
Roll-gerotor set has teeth fitted with rollers. The rollers reduce local stress and the tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.
Roll-gerotor sets are recommended for operation with thin oil and for applications with continually reversing applications with continually reversing loads. GR, GRS series motors have roll-gerotor set.
APPLICATION
» Conveyors
» Feeding mechanism of robots and manipulators
» Metal working machines
» Textile machines
» Agricultural machines
» Food industries
» Grass cutting machinery etc.
OPTIONS
» Model-Spool valve, roll-gerotor
» Flange mount
» Motor with needle bearing
» Side and rear ports
» Shafts: straight, splined and tapered
» Shaft seal for high and low pressure
» Metric and BSPP ports
» Speed sensoring
» Other special features
GENERAL
Max.Displacement | cm3/rev | 397 | ||
Max.Speed | RPM | 970 | ||
Max.Torque | Nm |
cont.:610 |
int.:690 | |
Max.Output | KW | 15 | ||
Max.Pressure Drop | Mpa |
cont.:17.5 |
int.:20 | |
Max.Oil Flow | lpm | 75 | ||
Min.Speed | RPM | 10 | ||
Pressure Fluid | Mineral based-HLP(DIN 51524) or HM(ISO 6743/4) | |||
Temperature Range | -40 to 140 | |||
Optimal Viscosity Range | mm2/s | 20 to 75 | ||
Filtration | ISO code 20/16 (Min.) (recommended fluid filtration of 25 microns) ISO 20/16 |
Specification data for GR series motor
Displacement(cm3/rev) |
GR 50 |
GR 80 |
GR 100 |
GR 125 |
GR 160 |
GR 200 |
GR 250 |
GR 315 |
GR 400 |
|
51,5 |
80,3 |
99,8 |
125,7 |
159,6 |
199,8 |
250,1 |
315,7 |
397 |
||
Max Speed | Cont. |
775 |
750 |
600 |
475 |
375 |
300 |
240 |
190 | 0 |
Int.* |
970 |
940 |
750 |
600 |
470 |
375 |
300 |
240 |
190 |
|
Max Torque | Cont. |
100 |
200 |
240 |
300 |
390 |
385 |
390 |
360 |
380 |
Nm | Int.* |
130 |
220 |
280 |
340 |
430 |
460 |
470 |
470 |
470 |
Peak** |
170 |
270 |
320 |
370 |
460 |
560 |
600 |
610 |
610 |
|
Max Output | Cont. |
7 |
12,5 |
13 |
12,5 |
11,5 |
9 |
8 |
5 |
4,8 |
Int.* |
8,5 |
15 |
15 |
14,5 |
14 |
12 |
9,5 |
8 |
6,8 |
|
Max Pressure Drop | Cont. |
14 |
17,5 |
17,5 |
17,5 |
17,5 |
14 |
11 |
8,5 |
6,5 |
Mpa | Int.* |
17,5 |
20 |
20 |
20 |
20 |
17,5 |
14 |
11,5 |
9 |
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
20 |
15 |
11,5 |
|
Max Oil Flow | Cont. |
40 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
Int.* |
50 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
|
Max Inlet Pressure | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
Max.Return Pressure with Drain Line | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
Max.Starting Pressure with Unloaded Shaft |
1 |
1 |
1 |
0,9 |
0,7 |
0,5 |
0,4 |
0,3 |
0,3 |
|
Min Starting Torque | At max.press. drop Cont. |
80 |
150 |
200 |
250 |
320 |
330 |
310 |
315 |
315 |
At max.press.drop Int.* |
100 |
170 |
230 |
280 |
370 |
400 |
480 |
580 |
500 |
|
Min.Speed |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
|
Weight(kg) | MR(F) |
6,8 |
6,9 |
7,2 |
7,3 |
7,5 |
8 |
8,4 |
9,1 |
9,8 |
MRQ(N) |
6,2 |
6,3 |
6,6 |
6,8 |
7,6 |
7,2 |
7,8 |
8,6 |
9,3 |